PCB failures (Such as WD PCB 2060-771801-*** (2061-771801-***)<\/b>) affect thousands of hard drives every year and often result in permanent data loss. A hard drive may suddenly fail to power on, and a computer may not detect that it is plugged in. Some failed hard drives will also show up in computer BIOS with incorrect brand\/model information. PCB failures can also cause physical issues such as read\/write head failures, and many PCB failure symptoms overlap with the symptoms of other physical hard drive issues.<\/p>\n
Some emails from customers of WD PCB 2060-771801 failures are listed below, along with tips for replacing & repairing.<\/p>\n
Q: Transfer ROM 771801 -> 771823?<\/b><\/p>\n
Hi, I wish to recover the USB3.0 WD Passport having controller “771801”. According to the information is this sub-category, the matching SATA controller is 771823. However, as seen from the attached pictures, the ROM chip, U12, is different physically – the newer, 771823 controller has the solder legs Under the U12 chip but the Patient controller, 771801 has regular solder legs. – I think they …<\/p>\n
Q: W.D Passport<\/b><\/p>\n
I have a 1TB WD10JMVW with integrated USB 3.0 connector Logic Board number 2060-771801-002 Rev A Is there a standard SATA board I can swap this out for to make it easier for data recovery? Thanks in advance Mark<\/p>\n
Q: PCB id 771801 vs 771823<\/b><\/p>\n
Hi all, I have question about original usb drive wd with pcb id : 771801 and donor sata pcb id : 771823. assume original head and rom good. and donor pcb 771823 good.. so rom original + pcb donor install on original drive. what happen ? it direct can get data from this sata drive or need back to original usb drive after repair use sata board ? Thanks,. Jinarto<\/p>\n
Q: List of compatible SATA PCB for 2,5″ USB drives<\/b><\/p>\n
USB – SATA 701605 – 701499 701615 – 701499 701635 – 701572 701650 – 701499 701675 – 701672, 701609, or 771672 771737 – 701692 or 771692 771754 – 701692 or 771692 701754 – 771692 771761 – 771692 771801 – 771823 771814 – 771820 771859 – 771852 771949 – 771959 or 771939 771961 – 771960, 771939, or 771959 771962 – 771931 or 771959 771817 – 771820 800041 – 800022 800038 – 800025 800069 – 800066 800067 – 800065 810012 – 800022 If somebody knows another compatible boards, …<\/p>\n
Q: WDCC data decryption card, a new tool?<\/b><\/p>\n
hard drive, support for the brand have Western Digital Seagate, Toshiba, Samsung, Lenovo The WDCC-A support symwave sw6316 master board is 2060-771737-000 (WD10TMVW-11ZSS1) The WDCC-B support jms538s controller chips, circuit boards for 2060-771801-002 (WD5000BMVW-11S5XS0) 2060-771714-001 The WDCC-C supports Seagate HDD<\/p>\n
Q: WD Smartware USB 2 and 3 PCB`s for SALE\/TRADE<\/b><\/p>\n
Guys,i have stock of those WD Smartware PCB`s for SALE\/TRADEUSB2 & USB3 – All TypesSamples here:771737771801771761771754701675and more least 70-80p from each (some are even more), wanna get rid of those and sell them or trade them with 3.5″ WD, Hitachi, Samsungif anyone is interested PMthnx<\/p>\n
Q: Info about SATA-USB compatible WD board<\/b><\/p>\n
Hello,can you tell me a SATA board compatible with USB board 2060-771801-002 REV P1?It is from a WD5000BMVW-11S5XS0 Is 771823 compatible?Many thanks!Simone<\/p>\n
Q: Firmware Reguest For WD5000BMVW-11S5XS0<\/b><\/p>\n
Hi ALLI have a FW problems HDD WD5000BMVW-11S5XS0model: WD5000Bmvw-11S5XS0.PCB Number: 2060-771801-002 Rev A.i use HD Doctor for WD scan , it errorAnyone have a FW donate for me pleaseThank you very much ALL..email : thailandfix(at)hotmail.com<\/p>\n
Q: WD10JMVW Write Protected USB Drive<\/b><\/p>\n
The above drive is not being recognized. I have a matching USB board (rather than a SATA donor). Original board is 2060-771801-002-REV A. The donor is identical but from a 2TB WD drive. Swapped the U12 chip. Drive name up in R-Studio, but as write protected. The drive is seen in Device Manager but as unallocated space. I presume this is an encryption issue? I also swapped U14 as a test but the drive clicked. Any help would be appreciated.<\/p>\n
Q: Looking for 2TB WDhard drive<\/b><\/p>\n
I am looking for this parts drive. Please provide links or details if you have this drive or know where to find it.Western Digital 2 TB Hard Drive Specs-Model # – WD20NMVW-11W68S0DCM- HBCVJBKBPCB # 2060-771801-002 Rev P1<\/p>\n
Q: Buy Hard Drive 2Tb WD<\/b><\/p>\n
I am looking for this parts drive. Please provide links or details if you have this drive or know where to find it.Western Digital 2 TB Hard Drive Specs-Model # – WD20NMVW-11W68S0DCM- HBCVJBKBPCB # 2060-771801-002 Rev P1<\/p>\n
Q: Need Donor for WD<\/b><\/p>\n
WD10JMVW-11S5XS0DCX : ES0C5CWXDCM : EHCTJBBBDATE : 05 NOV 2012PRODUCT : THAILANDPCB : 2060-771801-002 REV Athanks to all…<\/p>\n
Q: WD Passport: Repair\/exchange fried usb port<\/b><\/p>\n
Hi there, I have a Western Digital WD Passport USB 30 WD10JMVW 1TB , MDL WD10JMVW-11S5XS0 , PCB board number 2060-771801-002 REV A After analysis I’m 95 percent sure that the USB port and\/or controller is fried up and the HDD should work properly any chance to repair it without swapping PCB board? www com\/itm\/PCB-Controller-board-2060-771801-002-WD10JMVW-11S5XS0-Festplatten-Elektronik-\/301663775660?hash=item463c8febacgBmIAAOSweW5VgArc#viTabs_0 <\/p>\n
Q: WD My Passport WD10JMVW recovery<\/b><\/p>\n
beeps) then spins down and tries to spin up again with same beeping sequence (this time repeats it 3 times) I attached the audio here The disk has the PCB board with USB connector which I’ve already tried to replace with identical PCB (2060-771801-002) Also rom chips has been transferred to the replacement pcb but still the same beeping symptoms occurs Disk has been opened in clean room for observation but there’s no visible damage on top platter and heads are parked nicely to the ramp <\/p>\n
Q: WD5000BMVW-11AMCS0,WD10JMVW-11S5XS0,ST2000DM001,Samsung<\/b><\/p>\n
B0F\/2831 11 B4F\/2895 23 B1B\/2843 – WD10JMVW-11S5XS0 DCMHBOTJBB DATE 01 JUN 2013 Board2060-771801-002 REV A Sticker771801-002 AND28 – ST2000DM001 P\/N9YN164-021 FWHP16 Site SU S\/N W24* <\/p>\n
Q: Advice on recovery for a WD My Passport 2TB USB drive<\/b><\/p>\n
Hi folks, looking for advice on recovery options for a Western Digital My Passport (2TB) USB drive A colleague sent this drive to me Drive details Model WD20NMVW-11W68S0 Date 28 SEP 2012 PCB 2060-771801-002 REV A Symptoms and behaviour, from start of drive being plugged in (behaviour is the same, tested on both Windows 7 as well as FreeBSD) 1 Access LED is steady for about half a second 2 Drive spins up 3 Access LED blinks (LED on\/off interval ~025s) 4 After <\/p>\n
Q: WD Passport USB transfer to compatible SATA Circuit PCB<\/b><\/p>\n
WD USB to SATA PCB data recovery Today me share the following model compatible PCB SATA 701605 – 701499 701615 – 701499 701635 – 701572 701650 – 701499 701675 – 701672, 701609, or 771672 771737 – 701692 or 771692 771754 – 701692 771761 – 771692 771801 – 771823 771814 – 771820 771859 – 771852 771949 – 771959 or 771939 771961 – 771960, 771939, or 771959 771962 – 771931 or 771959 771817 – 771820 800041 – 800022 701675-001 – 701672-001 External ROM 88I9045-TJF2 701675-001 – 701609-004 No External <\/p>\n
Q: WD5000BMVW-11S5XS0<\/b><\/p>\n
Hello!I have received the drive in topic (WD5000BMVW-11S5XS0 – FireBird – 2060-771801-002) with completely fried ROM and 2 missing legs. I have connected ROM IC to programmer but unfortunately, all I get in hex is (FF).I have tried several ROM’s and LDR’s but no luck. No access to SA to determine the correct version of original ROM.Any suggestions would be highly appreciated.Thanks in advance.<\/p>\n
Q: Is U14 EEPROM swap necessary for MyPassport board swap?<\/b><\/p>\n
I have a WD MyPassport 10TB external USB hard drive with a 2060-771801-002 Rev A board (more specs below) My end goal here is just to recover the data Board appears to have some kind of water\/chemical corrosion damage Both U12 and U14 EEPROM chips are Winbond 25x20blnig 2MBit\/256Kb chips I was able to sucessfully backup the contents of the U12 ROM chip using a CH341A programmer w\/ SOIC clmap, but <\/p>\n
Q: Change PCB WD10JMVM-11S5XS0<\/b><\/p>\n
I have a USB hard drive WD10JMVM-11S5XS0 withPCB: 2060-771801-002 REV. A and I tried to put aPCB: 2060-771823-000 REV. A and when I transferred the ROM, the PCBdoes not respondDoes anyone know any compatibility with this PCB?Thanks in advance<\/p>\n
Q: Western Digital USB-SATA PCB Package<\/b><\/p>\n
DFL is offering a package containing “all the compatible SATA PCBs for the most common USB PCBs including USB PCB 701605, 701615, 701635, 701675, 771737, 771754, 771761, 771801, 771814, 771817, 771859, 771961, 80038, 800041(3TB)” https\/\/wwwdolphindatalabcom\/product\/western-digital-usb-sata-pcb-package\/ Anyone have any thoughts or input about this? Seems like it may be a good deal if these are actually the most common boards I’m still waiting <\/p>\n
Q: WD 1TB WD10JMVW-11S5XS1 spins, enumeration failure<\/b><\/p>\n
of our company that was backing up pictures to an external HDD without any other sort of online-based backup This model of external 25″ Hard Drive is a USB 30 only PCB (my first thought was to plug it into SATA) Here is the board 2060-771801-002 Rev A I found the board here https\/\/wwwhdd-partscom\/15120649html ~ The symptoms are as follows – When plugging into any computer or USB port, I instantly get a windows device connection sound – The device is powered up and spinning <\/p>\n
Q: WD10JMVW-11S5XS0<\/b><\/p>\n
localphysical in the ROM riddles me roll pcb is OK, head #4 seems troublesome in the process of acquiring a donor drive Thanks a lot in advance! Model WD10JMVW-11S5XS0 Date 26 JAN 2013 DCM EBMTJBK Product of Malaysia PCB Revision 2060-771801-002 REV A 01129\/4393 110EE\/4334 210F8\/4344 31140\/4416 <\/p>\n
To repair a failure board, the simple way is swapping the failure board with a replacement board. Donor boards on HardDriveParts.com are listed below:<\/p>\n
PCB failures (Such as WD PCB 2060-771801-*** (2061-771801-***)) affect thousands of hard drives every year and often result in permanent data loss. A hard drive may suddenly fail to power on, and a computer may not detect that it is plugged in. Some failed hard drives will also show up in computer BIOS with incorrect brand\/model information. PCB failures can also cause physical issues such as read\/write head failures, and many PCB failure symptoms overlap with the symptoms of other…<\/p>\n