WD PCB 2060-771961 Failure

WD PCB 2060-771961 Failure

PCB failures (Such as WD PCB 2060-771961-*** (2061-771961-***)) affect thousands of hard drives every year and often result in permanent data loss. A hard drive may suddenly fail to power on, and a computer may not detect that it is plugged in. Some failed hard drives will also show up in computer BIOS with incorrect brand/model information. PCB failures can also cause physical issues such as read/write head failures, and many PCB failure symptoms overlap with the symptoms of other physical hard drive issues.

Some emails from customers of WD PCB 2060-771961 failures are listed below, along with tips for replacing & repairing.

WD PCB 2060-771961 Failures:

Q: WD10JMVW-11AJGS3 Donor

Hello, I have a case to recover data from WDC 1TB USB – FBlite. MDL: WD10JMVW-11AJGS3. DCM: EHMT2HK. DATE: 03 SEP 2015. Product of Malysia. PCB: USB 2060-771961 changed to SATA 2060-771960 working good. Needed compatible heads donor Thank you for help.

Q: wd20nmvw-11av3s2 Rom Transfer from usb pcb to Donor pcb

I have Hard disk wd20nmvw-11av3s2 and I like to Transfer Rom from usb pcb to Donor pcb . I believe this drive has slow response issue so planing to change from usb pcb to sata so i am looking for any documentation can help me to transfer the rom from this 2060-771961-001 rev A TO 2060-771960-000-REV A This 2060-771961-001 has 12 pins so i like to know how we can setup com connection how i can transfer rom information from one pcb to other pcb Thanks

Q: How to select sata PCB compatible with the one USB PCB 2060-771961-001

Hi This is my fist post i’m new with data recovery how to select the right sata PCB compatible with that one USB i have this usb hard drive :WD10JMVW-11AJGS2 PCB: 2060-771961-001 To find the right PCB what I have look at is.. I am new at the word of data recovery i bought pc-3000 express with ssd one more question when i recieve a hard drive how do i know that i need to change a pcb or head or do i need to do a clean room thank you very much in advance …

Q: Task Error in DE

Hi guys I hope someone can help out I have got a WD WS20NMVW-11EDZS6 2TB USB Drive The drive was not spinning up correctly. I changed the logic board from its original USB PCB 0260-771961-001 Rev B to a SATA PCB 0206-771960-000 Rev A I also swapped the U12 BIOS IC over to the SATA PCB. The drive now shows a “Ready State” when drive is first powered up, when I then open a new task the system throws up an error saying “Error : Create Task – DeterminateSource …

Q: How to solve SED problem in 2,5″ WD drives

… to SATA (using a compatible SATA PCB or SATA adapter), but when we start Marvell utility we see SED locked error. 1. Start the drive in Kernel mode: head isolation with connected spindle contacts or short E47 PCB pin to the ground (tested on 2060-771961-000 REV P1). Status registers will be off, ID is not detected, but autodetect should work correct. ?2. Follow Work with ROM->SA regions editor->Do it now.. button …

Q: List of compatible SATA PCB for 2,5″ USB drives

… 701615 – 701499 701635 – 701572 701650 – 701499 701675 – 701672, 701609, or 771672 771737 – 701692 or 771692 771754 – 701692 or 771692 701754 – 771692 771761 – 771692 771801 – 771823 771814 – 771820 771859 – 771852 771949 – 771959 or 771939 771961 – 771960, 771939, or 771959 771962 – 771931 or 771959 771817 – 771820 800041 – 800022 800038 – 800025 800069 – 800066 800067 – 800065 810012 – 800022 If somebody knows another compatible boards, please write it here in this topic.

Q: sata port on wd passport usb 3.0

Hello, I’m searching the pinouts to solder a sata port on a wd USB 3.0 pcb? The pcb model is : 2060-771961-001 rev a. Thanks Fran?ois

Q: How to select the right Sata PCB compatible with the one USB

Hello everyone,. this is my first post. I was wondering if there is a criteria in selecting the right Sata PCB, compatible with that one USB.. For example I have this drive usb: WD5000BMVW-11AJGS0. PCB: 2060-771961-001 REVA. To choose the right PCB what I should look?. Thank you very much in advance for any hint or advice.

Q: WD20NMVW-11AV3S2-2060-771961 usb board

WD20NMVW-11AV3S2-2060-771961 usb board what board would I use to convert to sata. . is this model supported? thanks

Q: MODEL:WD10JM1VW belongs to which family

hello sir,. i have wd 1tb ext usb drive MODEL:WD10JM1VW is detected by windows too but it becomes too slow.in my pc3k v5.5 drive cant take family so i m unable to use slow read option.Aswell unable to create head map.Can u pls help me my pcb no is :2060-771961-000 rev p1 can u pls suggest cross pcb.marwel no is:88i9446-NDB2 ROM IS :25U20A. Or anybody tell me which family i should choose.

Q: [Desperate] WD Elements SE Portable 1TB dead

have the money necessary to consult a DR expert Unless you have any other idea Any help would be greatly appreciated Product name WD Elements SE Portable 1TB Product number WDBPCK0010BBK-01 HDD Model WD10JMVW-11AJGS0 Board number 2060-771961-000 REV P1

Q: 771961 USB to SATA

Which SATA PCB is mostly compatible with this PCB?Tested one?2060-771961-000 USB PCB

Q: SATA pcb no for 2060-771961-001

Please suggest SATA PCB for 771961 USB mounted on WD10JMVW-11AJGS1, 1 tb DRIVE.Thanx

Q: USB 3 to SATA

Please suggest SATA pcb for 771961. I tried with 771959 , but it does not work with WD tool to repair FW.This can help to connect only to connect the drive with computer sata port and power supply is given only through USB port.So please suggest SATA PCB which can be used to repair FW on WD fw repair tool.Thanx

Q: WD external drive extremely slow

2TB drive that is extremely slow Data is about 350GB and very important on it and I would be glad to get all data off of it First of all, it has only USB connection, so I cannot connect it to SATA The drive model is WD20NMVW PCB number 2060-771961-001 REV A When connected to computer it is not recognized immediately, only after few minutes it appears in Disk management After that, reading folder structure takes very long time When trying to copy data off, 1MB copies 10 minutes It

Q: WD10JMVW-11AJGS1

Patient:WD10JMVW-11AJGS1PCB: 771961MALAYSIADONORWD10JMVW-11AJGS3PCB: 771961MALAYSIAHEADS COMPATIBLE?WD PASSPORT SERIES

Q: WD My Passport 1 TB Drive – Fails recognition in Windows

Hi, Just joined this good forum I have a problem with my WD my passport 1 TB drive (Model WD10JMVW 2060-771961-001 REV) The drive suddenly stopped being recognized in Windows The available space is shown as 0 bytes The drive can not be accessed Smartware status is – No smartware area found Following is status for the drive in Data Lifeguard when I run extended test, Test Option EXTENDED TEST Model Number WD My Passport

Q: WDC PCB Exists ? -> XXXX-771939-XXX

Hello , I was referring to data medics forums – > https//wwwdata-medicscom/forum/viewtopicphp?f=25&t=13 In This We Have a Line That For USB Number 771961 We Can Use PCB No 771959 or 7717939 or 771960 I had ordered 771959 But the Holes Orientation is all different in the 771959 you cannot install it properly on 771961 So i asked my supplier for 771939 and 771960 to which he quotes me for 771960 but said 771939 does not exist Any Comments

Q: Western Digital Passport Repair

in the bottom corner -Device shows up for “Safe to Remove Hardware” (I have tried on two Windows 7 computers and a Windows 81 computer, results same on both) So, I found a PCB for this HDD www com/itm/WD20NMVW-2060-771961-000-2TB-Western-Digital-WD-Passport-PCB-Firmware-Transfer-/231577575831?pt=LH_DefaultDomain_0&hash=item35eb196197 Is it possible that replacing the PCB could fix this? Thanks a ton to anyone that helps out,

Q: WD My Passport Ultra 2TB problem 🙁

forumhddgurucom/viewtopicphp?f=1&t=29500&p=220025#p220025 I have similar problem, like in link above WD My Passport Ultra 2TB, HDD model inside WD20NMW-11AV3S2 and PCB 2060-771961-001 REV A One day it stopped working, no clicking noises, it spins starts moving head and after some time it stops spinning and starts again immediately again to spin I suspected that it was head problem So I ordered same disk, same specs and disassembled Replaced

Q: WD My passpot 1 TB 2060 771961 001 revA not working.

Hi,WD My passpot 1 TB board : 2060 771961 001 revA. is not working.Please checked here ?to understand the issue and photo Attachment:IMG_20150917_131906.jpg [ 1.42 MiB | Viewed 3926 times ].I am not sure what is the issue. please suggest next steps to recover data from this hard drive.Regards,Kishor

Q: WD10JMVW-11AJGS2 Recovery

Problem 1 hdd is not detected via usb 2 PCB 771961(usb) Steps Taken 1 PCB 771961(USB) replaced by 771959 (SATA) 2 ROM Chip U12 Transferred Status 1 Not Detected by bios and windows 2 SPIN and No Clicking Sound 3 In WDR 60 detected as WDC ROM MODEL-FBLITE- FW1656H SNWDC-ROM SN# XYZ—- (ROYL selected) port 0xF0C0 Logical Cyls 0, Heads 0, Sectors 0, LBA 0, 0Gb Controller Buffer Size

Q: WD10JMVW-11AJGS2(USB to SATA) Recovery

HDD WDC WD10JMVW-11AJGS2 WD-WXJ1EA3LZFH5 Type USB 30 PCB 771961(usb) Status Detected by Bios and windows with all partitions and Files Problem Read Very Slow 70KB/S Steps Taken 1 PCB 771961(USB) replaced by 771959 (SATA) 2 ROM Chip U12 Transferred After usb to sata pcb changed, HDD is visible with partitions and files Then tried to apply slow fix WDR 60 Identifies the hdd but can’t read any

Q: WD my passport ultra not detect

hi guysi hav a WD20NMVM-11EDZS2 that it detect as not initialized dist in disk managmenti try to conncet as sata (remove c13,c18,c37,31 and connect E71=A+,E72=A-,E73=B-,E75b+)but it not work and just led blinkingboard number is 2060-771961-001 rev Bi need datai have mrt pro what should i do?tnx

Q: WD Passport USB transfer to compatible SATA Circuit PCB

PCB SATA 701605 – 701499 701615 – 701499 701635 – 701572 701650 – 701499 701675 – 701672, 701609, or 771672 771737 – 701692 or 771692 771754 – 701692 771761 – 771692 771801 – 771823 771814 – 771820 771859 – 771852 771949 – 771959 or 771939 771961 – 771960, 771939, or 771959 771962 – 771931 or 771959 771817 – 771820 800041 – 800022 701675-001 – 701672-001 External ROM 88I9045-TJF2 701675-001 – 701609-004 No External ROM 88i8946-TJF2 701609-000 – 701675-001 Good luck

Q: WD USB swap to sata, 0GB ,what’s next?

a U14 chip, which does not exist in the sata board( research from forum says it’s a encryption chip) I load up using MRT i manually picked family group “shrek LT” as it doesn’t auto detect Shows 0 GB WD20NMVW-11AV3S0 original board 771961 SATA donor board 771960 it shows Technology mode key OK RAM Read HDD Info OK Heads number 8 Head map

Q: Drive will not initialize, reporting CRC errors

was performed in Home-built “clean-air” box, two-stage HEPA-filtration (actual filtration not tested with any device that measures particulate count) Troubled drive Make Western Digital MDL WD10JMVW-11AJGS1 DCM EHKT2HK PCB 2060-771961-001 REV-A / Sticker 771961-001 AH Date 11 JUL 2014 Location Malaysia Interface USB 30 First donor (did see drive capacity, but would not initialize) Make Western Digital MDL WD10JMVW-11AJGS2 DCM HBKT2HK PCB 2060-771961-001 REV-B /

Q: Slow responding WD20NMVW-11AV3S2

Hi, I’ve got a slow responding WD20NMVW-11AV3S2. The PCB is 2060-771961-001 REV A. What’s the best way to recover Data von this HDD?I think, there are two ways. The first one is to solder on some wires to the PCB to get SATA connection. Another way would be a board swap with U12 swap. But AFAIK the Data on the WD Drives is encrypted. How to deal with it? Swap the PCB again, when I fixed the slow responding problem with PC3k?

Q: WD My Passport Ultra, no partition map and slow reads

Hello, Newbie here I have a WD My Passport Ultra 1TB with a 2060-771961-001 PCB that wasn’t being recognized by the computer at all The LED would flash a few times, then go steady, then flash again It seemed to spin up fine and I didn’t hear any clicking I followed this guide here forumhddgurucom/viewtopicphp?f=1&t=27819 I removed U14, then desoldered C13, C18, C31, C37 from the JMS

Q: WD My Passport Ultra USB PCB to SATA PCB Swap for Recovery

Manager, but is otherwise not recognized or visible (as a drive) in any operating system or software recovery applications used I’d like to use our DeepSpar on it, but we don’t have the USB add-on for it yet I’d like to swap the USB PCB (2060-771961-001) to a compatible SATA PCB so that we can use the DeepSpar on it Drive Info WD My Passport Ultra WD Green Model WD20NMVW-11AV3S2 Date 08 MAR 2015 Questions – What would be the recommended SATA PCB? (and where best to get it?) – Do I

Replacement WD PCB 2060-771961:

To repair a failure board, the simple way is swapping the failure board with a replacement board. Donor boards on HardDriveParts.com are listed below:

Contact US

If you have any questions, please feel free to contact us: sales@harddriveparts.com

Comments are closed.